推 aw25282 : 推 Tt 02/26 00:16
http://shadowsfalltw.gjisland.net/?p=3990
--
Core 系列最早是從上位,支援 EATX 的 V71 開始發表,然後是中塔 V51,另外還有一款
尚未在台灣販售的 Core V41 外觀規格則位於 V51、V31 之間;然後則是接下來則是這次
開箱的,外觀尺寸上較小的 V31,當然內部擴充性的支援也有些差異。另外還有專供
mATX 以及 ITX 機殼用的型號就不在這次的範圍之內。
產品外箱:
http://shadowsfalltw.gjisland.net/pic/ttcorev31/corev31_01.JPG
節錄自官方的冷排支援以及規格諸元:
http://shadowsfalltw.gjisland.net/pic/ttcorev31/support.JPG
http://shadowsfalltw.gjisland.net/pic/ttcorev31/v31spec.JPG
本體:具有透明側版。另外大量孔洞的前面板已經是 Core 系列機殼共通的特色。
http://shadowsfalltw.gjisland.net/pic/ttcorev31/corev31_02.JPG
前面板部分提供兩個 5.25”,其中一個可轉換成 3.5” 外接裝置;前面板IO 部分則是
僅提供兩個 USB 3.0、耳機、麥克風、電源、RESET與燈號。
http://shadowsfalltw.gjisland.net/pic/ttcorev31/corev31_03.JPG
http://shadowsfalltw.gjisland.net/pic/ttcorev31/corev31_04.JPG
面板內部:風扇開口完全沒有任何阻擋,螺絲固定孔也是可上下移動微調來配合冷排實裝
以後可能多占用的空間,但是前面板內並沒有濾網。
http://shadowsfalltw.gjisland.net/pic/ttcorev31/corev31_05.JPG
http://shadowsfalltw.gjisland.net/pic/ttcorev31/corev31_06.JPG
上方的 5.25” Drive Bay 也是可以拆除配合空間需要作調整,或者是用來安裝硬碟或
SSD。5.25 Drive Bay 可以透過內部的孔位安裝兩顆 2.5” 硬碟,或是一顆 3.5” 硬碟
而不需要俗稱小翅膀的延伸轉接架。
http://shadowsfalltw.gjisland.net/pic/ttcorev31/corev31_07.JPG
頂部全開孔:濾網為軟性材質並且邊緣具有磁性可吸附在外殼之上,方便拆洗。拔除濾網
之後可看到內部開孔為蜂巢狀,風扇螺絲孔位也同樣可移動微調,可支援140mm、120mm風
扇或是最大360冷排。
http://shadowsfalltw.gjisland.net/pic/ttcorev31/corev31_08.JPG
http://shadowsfalltw.gjisland.net/pic/ttcorev31/corev31_09.JPG
內部架構:內部可見大量模組化設計所需要的孔位,背面開孔與內部強度與目前相近價位
配置產品差不多,PCI檔版以及背部水管出入口周邊皆採開孔設計。後方出風風扇為12CM
,螺絲孔位也同樣非固定,可以上下微調位置。另外主機板安裝孔使用銅柱,並出廠時已
在ATX/MATX 共用孔位預先裝上所需銅柱。
http://shadowsfalltw.gjisland.net/pic/ttcorev31/corev31_10.JPG
http://shadowsfalltw.gjisland.net/pic/ttcorev31/corev31_11.JPG
http://shadowsfalltw.gjisland.net/pic/ttcorev31/corev31_12.JPG
http://shadowsfalltw.gjisland.net/pic/ttcorev31/corev31_13.JPG
硬碟架部分,Core 系列機殼都採模組化設計,V31配置一個可容納 3 顆 3.5 HDD 的硬碟
架,可以依照配置的要求來上下移動硬碟架位置,托盤部分也可透過底部的孔位來安裝
2.5” 硬碟,底層可以安裝兩顆 120mm 風扇,但要注意得將硬碟架底層的滑軌拆除,才
不會擋住風道。
http://shadowsfalltw.gjisland.net/pic/ttcorev31/corev31_14.JPG
http://shadowsfalltw.gjisland.net/pic/ttcorev31/corev31_15.JPG
http://shadowsfalltw.gjisland.net/pic/ttcorev31/corev31_16.JPG
http://shadowsfalltw.gjisland.net/pic/ttcorev31/corev31_17.JPG
http://shadowsfalltw.gjisland.net/pic/ttcorev31/corev31_18.JPG
下置電源的部分使用制震墊來防震,另外防塵濾網覆蓋面積也加大,以應付來自下方增加
風扇的不時之需,不過拆卸上就比較不方便些。
http://shadowsfalltw.gjisland.net/pic/ttcorev31/corev31_19.JPG
http://shadowsfalltw.gjisland.net/pic/ttcorev31/corev31_20.JPG
背面部分:主機板底板與硬碟架間以鉚釘固定,背部可擴增兩顆 2.5” 硬碟,當然也能
依配置來改變位置。走線孔的部分也相當充足。
http://shadowsfalltw.gjisland.net/pic/ttcorev31/corev31_21.JPG
http://shadowsfalltw.gjisland.net/pic/ttcorev31/corev31_22.JPG
http://shadowsfalltw.gjisland.net/pic/ttcorev31/corev31_23.JPG
http://shadowsfalltw.gjisland.net/pic/ttcorev31/corev31_24.JPG
配件一覽:
http://shadowsfalltw.gjisland.net/pic/ttcorev31/corev31_25.JPG
試裝上機:因為僅配置1個硬碟架,所以空間算是相當夠,也有不少空間可以發揮走線創
意。散熱器部分使用了全高約在 15 CM 左右的 Venomous X 大概就是上限了。
http://shadowsfalltw.gjisland.net/pic/ttcorev31/corev31_26.JPG
http://shadowsfalltw.gjisland.net/pic/ttcorev31/corev31_27.JPG
http://shadowsfalltw.gjisland.net/pic/ttcorev31/corev31_30.JPG
背部一覽:走線與開孔大致上沒有太多問題,但是硬碟架背部的 SSD 架位置不算太優,
容易卡太多線材。另外 3.5” 硬碟區塊因為有多了固定的底板的緣故,即使已經有開孔
,使用 L 頭 SATA 線材會有干涉,導致只能使用直頭 SATA 線材。
http://shadowsfalltw.gjisland.net/pic/ttcorev31/corev31_28.JPG
http://shadowsfalltw.gjisland.net/pic/ttcorev31/corev31_29.JPG
--
模組化挺炫的,但是洞洞裝就看有沒有買單了
--
※ 發信站: 批踢踢實業坊(ptt.cc), 來自: 111.242.188.249
※ 文章網址: https://www.ptt.cc/bbs/PC_Shopping/M.1424868508.A.E57.html