Re: Corrupted partition table

At 8:01 PM -0700 9/24/04, Chris Pressey wrote:
>
>[...] the following would be *very* helpful:
>
>- the output of 'fdisk -s' from the DragonFly Live CD *before*
>   you start the install,
>- the file /tmp/install.log after the install is done (of course,
>   if the install doesn't work, getting that file will prove
>   difficult...

The install works, in the sense that I can boot up into Dragonfly.
(I have to go through some odd steps to get there, but it works)

>- the output of 'fdisk -s' after the install.

Before I go thru the whole install, let me see if the following
info will provide enough info to take a guess at things:

On the FreeBSD 5.3-beta5 system that I had installed first, I did:

     # fdisk -s
     /dev/ad4: 232581 cyl 16 hd 63 sec
     Part        Start        Size Type Flags
        1:          63    43005942 0xa6 0x00
        2:    43006005    24563385 0xa6 0x00
        3:    67569390    73722285 0xa5 0x80
        4:   141291675    93144870 0x83 0x00

I then wanted to change the sysid on the first DOS slice:

     # fdisk -u1
     ******* Working on device /dev/ad4 *******
     parameters extracted from in-core disklabel are:
     cylinders=232581 heads=16 sectors/track=63 (1008 blks/cyl)

     Figures below won't work with BIOS for partitions not in cyl 1
     parameters to be used for BIOS calculations are:
     cylinders=232581 heads=16 sectors/track=63 (1008 blks/cyl)

     Do you want to change our idea of what BIOS thinks ? [n]
     Media sector size is 512
     Warning: BIOS sector numbering starts with sector 1
    [...etc...]

After committing the change, I did:

     # fdisk -s
     /dev/ad4: 232581 cyl 16 hd 63 sec
     Part        Start        Size Type Flags
        1:          63    43005942 0xa5 0x00
        2:    43006005    24563385 0xa6 0x00
        3:    67569390    73722285 0xa5 0x80
        4:   141291675    93144870 0x83 0x00

I booted up on the Dragonfly CD.  The first minor hurdle is that
my hard disk is apparently installed as "ad4", so what I did was:

     # cd /dev
     # ./MAKEDEV ad4
     # fdisk -s /dev/ad4
     ad4: raw partition size != slice size
     ad4: start 63, end 43006004, size 43005942
     ad4c: start 63, end 234436544, size 234436482
     ad4: truncating raw partition
     ad4: rejecting partition in BSD label: it isn't entirely within the slice
     ad4: start 63, end 43006004, size 43005942
     ad4h: start 14563391, end 234436544, size 219873154
     /dev/ad4: 14593 cyl 255 hd 63 sec
     Part        Start        Size Type Flags
        1:          63    43005942 0xa5 0x00
        2:    43006005    24563385 0xa6 0x00
        3:    67569390    73722285 0xa5 0x80
        4:   141291675    93144870 0x83 0x00

I don't know if all those warning messages about "ad4:" are
significant, and I don't know if the fact that this is ad4 (and
not ad0) would be significant to the installation steps.  But I
suspect that it is significant that FreeBSD says:

        /dev/ad4: 232581 cyl  16 hd 63 sec
vs     /dev/ad4:  14593 cyl 255 hd 63 sec  on Dragonfly.

-- 
Garance Alistair Drosehn            =   [e-mail]
Senior Systems Programmer           or  [e-mail]
Rensselaer Polytechnic Institute    or  [e-mail]