Re: "atacontrol info" isn't working here

--ffoCPvUAPMgSXi6H
Content-Type: text/plain; charset=us-ascii
Content-Disposition: inline

Hi,

[ Cc'ing -doc@, so I put a little history from the thread in this mail ]

[ I forgot the Cc: field and the attached patch :-} ]

> > > > >I can use "list", "mode" and "cap" commands from atacontrol(8), but I
> > > > >can't use "info".
> > > > >
> > > > >%%%
> > > > >    jarjarbinks:root# atacontrol list
> > > > >    ATA channel 0:
> > > > >        Master:  ad0 <TOSHIBA MK8025GAS/KA023A> ATA/ATAPI revision 6
> > > > >        Slave:  acd0 <MATSHITAUJ-845D/D100> ATA/ATAPI revision 6
> > > > >    ATA channel 1:
> > > > >        Master:      no device present
> > > > >        Slave:       no device present
> > > > >    jarjarbinks:root# atacontrol info 0
> > > > >    atacontrol: Invalid channel 0
> > > > >    jarjarbinks:root# atacontrol info 1
> > > > >    atacontrol: Invalid channel 1
> > > > >%%%
> > > > >
> > >
> > > >for me atacontrol info ata0 works :)
> > >
> > >Thanks for your very quick answer.  I will send a patch to make the
> > >manual page more explicit for dumb peoples like me.
> > >  
> > Well it took me ten minutes too. Because that one is not obvious at all.
> > But I needed my cdrom (hotswap ide) and did not want to reboot.
> 
> I sent in a patch to the man page when this change was committed by sos@,
> but the man page has never been updated. I made the mistake of just
> posting and copying sos@. I should have put it in a PR.

Kevin, no news since then.  I made a patch for the manpage which is
actually clearly wrong :

%%%
	The channel argument is the number of the ATA channel on
	which to operate.
%%%

The ``channel'' argument is the name of the ata(4) device and not only
its number.

Regards,
-- 
Jeremie Le Hen
< jeremie at le-hen dot org >< ttz at chchile dot org >

--ffoCPvUAPMgSXi6H
Content-Type: text/plain; charset=us-ascii
Content-Disposition: attachment; filename="atacontrol.8_channel.diff"

Index: atacontrol.8
===================================================================
RCS file: /home/ncvs/src/sbin/atacontrol/atacontrol.8,v
retrieving revision 1.26
diff -u -p -u -r1.26 atacontrol.8
--- atacontrol.8	16 May 2005 15:09:13 -0000	1.26
+++ atacontrol.8	11 Aug 2005 04:38:00 -0000
@@ -88,7 +88,7 @@ exercise caution when using this command
 .Pp
 The
 .Ar channel
-argument is the number of the ATA channel on which to operate.
+argument is the ATA channel device on which to operate.
 The following commands are supported:
 .Bl -tag -width "rebuild"
 .It Ic attach
@@ -197,6 +197,11 @@ Show info about the attached devices on 
 Show info about all attached devices on all active controllers.
 .El
 .Sh EXAMPLES
+To see informations on devices attached on a channel,
+use the command line :
+.Pp
+.Dl "atacontrol info ata0"
+.Pp
 To see the devices' current access modes, use the command line:
 .Pp
 .Dl "atacontrol mode ad0"

--ffoCPvUAPMgSXi6H
Content-Type: text/plain; charset="us-ascii"
MIME-Version: 1.0
Content-Transfer-Encoding: 7bit
Content-Disposition: inline

_______________________________________________
[e-mail] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-doc
To unsubscribe, send any mail to "[e-mail]"

--ffoCPvUAPMgSXi6H--