[問題] SansAmp BDDI不會用...有人可幫我嗎>"<

[Ension (Eason)]

    各位親愛的前輩們大家好，小弟最近買了SansAmp Bass Driver DI，可是...裡面的說

明書看不太懂…想說有沒有已經有買過然後也看懂說明書的大大們幫小弟解惑一下…我只

知道旋鈕drive是破音…bass和treble是低頻和高頻（怎沒中頻@@"），然後其他就不知道

了…然後那3個按鈕更不知道是什麼QQ


6個旋鈕

【PRESENCE】
brings out the upper harmonic content and attack. For a smoother high end and
for clean settings, decrease to taste.

【DRIVE】
adjusts the overall amount of gain and overdrive, similar to when the output
section of a tube amp is being pushed.

【BASS & TREBLE】
unlike passive controls that only cut, these active tone controls cut or boost
±12dB from unity gain (12 o'clock). This powerful EQ section effectively
reduces the need for a fixed frequency mid control and enables you th achieve
an extensive variety of curves -including a "mid-cut" as well as a "mid-boost".

Adjusting Mid-Range Content: The mid-range level is preset. Boosting Bass and
Treble yields a "mid-cut" (at 750Hz) where the relative mid-range level is
higher than the Bass and Treble frequency levels. NOTE: The overall output
level will change relative to the EQ settings. Simply adjust the Level control
accordingly.

【BLEND】
allows you to blend the direct instrument signal with SansAmp Tube Amplifier
Emulation circuitry. In most cases, you will probably have this set at maximum
(100% SansAmp). For certain applications, however, such as an ultra-transparent
sound or for use with piezo pickup-equipped instruments, you may want to
blend-in some of the direct signal to achieve your desired sound. While the
SansAmp Tube Amplifier Emulation circuitry is bypassed when Blend is at minimum,
the Bass, Treble and Level controls remain active.

【LEVEL】
adjusts the output level of both the 1/4" and XLR outputs.


3個按鈕

【PHANTOM & GROUND CONNECT】
when engaged (depressed), the ground connects and unit will accept phantom
power through the XLR Output. Disengaged (up), the ground of your stage system
and other interconnected gear is lifted/isolated from the ground of the mixing
console.

【XLR OUT PAD】
-20dB pad to match the output to equipment with different input level
requirements. In the line level (up) position, the output is 0dB, In the
instrument level (down) position, the output is -20dB.

【1/4" OUT BOOST】
+10dB boost to match the output to equipment with different input level
requirements. In the instrument level (up) position, the nominal output is
-10dB. In the line level (down) position, the ouput is 0dB.

希望有好心的大大可以幫忙ˊˋ，感激不盡QQ

--
※ 發信站: 批踢踢實業坊(ptt.cc) 
◆ From: 123.194.130.123
推 UniFish     :請愛用字典
→ Ension      :查過了可是感覺很多配不起來ˊˋ
→ Ension      :然後像XLR...1/4"...這些根本不知道是什麼東西>"<
推 jimkung1202 :1/4"就是一般導線孔 XLR是平衡接孔(圓形內有三隻腳)
推 Likewhat    :同時砍高低頻 中頻就"凸"出來啦(無誤)
推 mikechang   :樓上說得沒錯XD  原文就是這樣寫的XD
→ mikechang   :中頻的頻率跟量是固定的，所以增加高低頻 = mid-cut
→ mikechang   :然後再搭配總音量的使用  多少可以達到調整中頻
→ Ension      :原來還有這樣!!又上了一課~感謝樓上大大們^^