推 blackkane:建議不要斜剖...會適得其反，直剖就好! 219.81.227.113 03/12 02:11
推 Haiker:!!我之前直剖會把粉塵留在碗公裡才改斜剖 59.104.162.134 03/12 02:15
推 Haiker:由內而外順著碗公跑的方向排掉才有效果吧 59.104.162.134 03/12 02:16
推 blackkane:我直剖斜剖各一顆...斜剖效果比較慘耶.. 219.81.227.113 03/12 02:16
→ blackkane:面對離合器在車上 我斜剖是左上到右下 219.81.227.113 03/12 02:17
→ blackkane:我都是單蹄片畫2條..要跑一段時間磨合 219.81.227.113 03/12 02:18
→ blackkane:幾百km後拆下來用砂紙打平 效果才出來 219.81.227.113 03/12 02:18
推 Haiker:怪怪，螺帽固定側在左手邊的話 59.104.162.134 03/12 02:19
→ blackkane:效果嘛..割的時候要穩...朋友沒割穩 219.81.227.113 03/12 02:20
推 Haiker:我是左上右下，剖溝順便拿砂紙磨粗 59.104.162.134 03/12 02:21
→ blackkane:效果是非常慘... 219.81.227.113 03/12 02:21
推 Haiker:碗公一樣拿粗一點的砂紙斜磨+畫圈 59.104.162.134 03/12 02:21
推 Haiker:我這樣做的效果很好說= =+溝要直倒是真的 59.104.162.134 03/12 02:22
→ blackkane:我車上斜剖這顆..(直剖那顆吃到油..) 219.81.227.113 03/12 02:22
→ blackkane:效果是時好時壞..我打算換碗公吧= = 219.81.227.113 03/12 02:23
→ blackkane:畫圈是在提片上畫?? 219.81.227.113 03/12 02:24
推 Haiker:我之前直剖那顆倒是很慘，有跟沒有差不多 59.104.162.134 03/12 02:24
推 Haiker:畫圈是在碗公畫，蹄片剖溝+砂紙磨粗就OK了 59.104.162.134 03/12 02:24
→ blackkane:還是我碗公根本就有問題勒...?? 219.81.227.113 03/12 02:25
→ blackkane:haiker大的提片吃滿還是吃中央而已? 219.81.227.113 03/12 02:25
推 Haiker:說不定喔XD 因為我問過不少前輩，都說斜剖 59.104.162.134 03/12 02:25
推 Haiker:蹄片喔，吃了3/4有吧，沒有只吃中央 59.104.162.134 03/12 02:26
→ blackkane:我想有可能是碗公有問題 當初換總成 219.81.227.113 03/12 02:26
→ blackkane:沒換碗公 全新離合器也是小打滑.. 219.81.227.113 03/12 02:27
→ frank543:吃到油..(抖)122.126.161.239 03/12 02:33
→ frank543:是油封爆了嗎? 是的話快換吧 不然很慘= =122.126.161.239 03/12 02:34
推 blackkane:拿下來清的時候撞倒機油瓶...哈哈哈.. 219.81.227.113 03/12 02:35
推 Haiker:XD 59.104.162.134 03/12 02:39
推 frank543:XD122.126.161.239 03/12 02:40
推 blackkane:XD 不要笑 原廠離合器也不便宜阿 XD 219.81.227.113 03/12 02:42
→ frank543:我懂你的心酸 XD (拍拍)122.126.161.239 03/12 02:44
推 blackkane:懂你還笑 囧 219.81.227.113 03/12 02:46
推 imanikki: 林喜咧歡喜啥? 61.62.245.53 03/12 14:58