課程名稱︰機械設計原理
課程性質︰系訂必修
課程教師︰尤春風
開課學院：工學院
開課系所︰機械系
考試日期（年月日）︰2009/11/12(四)
考試時限（分鐘）：14:20~17:40 (closebook+openbook)
closebook部分寫完交答案卷 才可領openbook部分
是否需發放獎勵金：是
（如未明確表示，則不予發放）
試題 :
Close book部分:
1.(10%，每一子題請用文字說明之，每一子題字數請勿少於100字)
(a) Please give the detail descriptions of the design processes and also
indicate the main requirements and goals of each stage.
(b) What are the decomposition approach and combinaiton approach on the
design processes?
(c) What are the top-down and bottom-up approach on the design processes?
2.(8%，每一子題請用文字說明之，每一子題字數請勿少於50字)
Please select one suitable material for the following components, and specify
the heat treatment process, if necessary.
(a) Hood(引擎蓋鈑) of the automobile bodies.
(b) Gear and pinion which is used to support the heavy loads.
3.(8%，每一子題請用文字說明之，每一子題字數請勿少於50字)
(a) Please give two methods of heat treatment for the low carbon steel.
(b) Please give two methods of heat treatment for the medium carbon steel.
4.(10%)
(a) Please state the distortion energy theory.
(b) Please use graphical representation to describe the distortion energy
theory if a biaxial stress state (σz=0) is used as an example.
(c) When a pure shear of the biaxial stress state is presented, how to find
the yielding strength in shear in term of the distortion energy theory.
5.(8%，(a)(b)請用文字說明之，(c)請用文字與圖說明之，每一子題字數請勿少於50字)
(a) What are redidual stresses?
(b) What are the causes of residual stresses?
(c) What are the shot peening processes?
6.(8%，每一子題請用文字說明之，每一子題字數請勿少於50字)
(a) At what condition, stress-concentration factor does not necessary to be
considered for the ductile material?
(b) At what condition, stress-concentration factor should be considered for
the ductile material?
7.(8%，每一子題請用文字與圖說明之)
(a) What is the Goodman line?
(b) Explain modified Goodman diagram for torsional shear stress.
Open book部分:
8. The rod shown in Fig.1 is made of AISI 1040 steel (ultimate strength
500 N/mm^2 , yield strength 400N/mm^2) and has two 90° bends. Use the
following criteria to determine the minimum rod diameter for a safety
factor of 2.0 at the most critical sections.
(a) Maximum shear stress theory
(b) Distortion energy theory.
300mm
▄▃▂▁
▄▃▂▁█▇▆▅▄▃▂▁
▇▆▅▄▃▂█◣
◢ ◤
◢ ◤
◢ ◤
◢ ◤
◢ ◤ 750mm
◢ ◤
◢ ◤
◢ ◤
50mm
z
▄▄──→100N ↑
／∣ ↙ →y
↙ ↓ x
1500N 800N
9. A straight,circular rotating simply supported beam with a 1000 mm length
has an axial load of 30,000 N applied at end and a ratial load of 800 N
applied at middle span of the beam. The beam is cold-drawn and the material
is AISI 1040 steel (ultimate strength 500 N/mm^2, yield strength 400 N/mm^2).
Find the minimum diameter of the safety factor 2.0 for infinite life by
using the following criteria:
(a) Goodman line
(b) Soderberg line.
Please note:
All factor for calculating the actual endurance limit can be set as 1.0.
--
那個圖....我盡力了~"~
請把它想成是一個三度空間的rod
沿+y方向300mm,轉向+x方向750mm,再轉向-z方向50mm
然後在最尾端受到xyz三個不同方向的力 這樣
給大家參考看看囉~
--
※ 發信站: 批踢踢實業坊(ptt.cc)
◆ From: 140.112.252.156
※ 編輯: jw771216 來自: 140.112.252.156 (11/16 20:50)