[請益] Arduino程式請教

[sdsd65676 (翻桌ING)]

各位先進好，小弟是剛接觸Arduino的新手

因為專題需求自己寫了程式碼，但是遇到了一些問題。

先附上我的程式碼

int a = 3;
int b = 2;
int c = 4;
int d = 7;
int e = 8;
int f = 12;
void setup() {
  // put your setup code here, to run once:
  pinMode(a, INPUT); //鑰匙開關;
  pinMode(b, INPUT); //檔位開關;
  pinMode(c, INPUT); //距離感知器;
  pinMode(d, INPUT); //靜音開關;
  pinMode(e, OUTPUT); //無聲輸出;
  pinMode(f, OUTPUT); //有聲輸出;

  if (digitalRead (a == HIGH), digitalRead(b == HIGH)
, digitalRead(d == HIGH)) //紅火 P檔 靜音, 無聲輸出;

  {
    digitalWrite(e, HIGH);
    delay(250);
    digitalWrite(e, LOW);
    delay(250);
  }
  if ( digitalRead (a == HIGH ), digitalRead(b == HIGH
, digitalRead(d == LOW)); //紅火 P檔 有聲, 有聲輸出;
  {
    digitalWrite(f, HIGH);
    delay(250);
    digitalWrite(f, LOW);
    delay(250);
    loop;
  }
  if ( digitalRead ([code]
  if ( digitalRead (a == LOW ), digitalRead (b == HIGH)
, digitalRead (d == HIGH)); //熄火 P檔 靜音, 無聲輸出5秒;

  {
    digitalWrite(e, HIGH);
    delay(5000);
    digitalWrite(e, LOW);
    delay(500);
    digitalWrite(e, HIGH);
    delay(500);
    digitalWrite(e, LOW);
    delay(500);
    digitalWrite(e, HIGH);
    delay(500);
    digitalWrite(e, LOW);
    delay(500);
    digitalWrite(e, HIGH);
    delay(500);
    digitalWrite(e, LOW);
    delay(500);
    digitalWrite(e, HIGH);
[code]
    delay(500);
    digitalWrite(e, LOW);
    digitalWrite(f, LOW);
  }
  if ( digitalRead (a == LOW ), digitalRead (b == HIGH )
, digitalRead (d == LOW )); //熄火 P檔 有聲, 有聲輸出5秒;
  {
    digitalWrite(e, LOW);
    digitalWrite(f, HIGH);
    delay(5000);
    digitalWrite(f, LOW);
    delay(500);
    digitalWrite(f, HIGH);
    delay(500);
    digitalWrite(f, LOW);
    delay(500);
    digitalWrite(f, HIGH);
    delay(500);
    digitalWrite(f, LOW);
    delay(500);
    digitalWrite(f, HIGH);
    delay(500);
    digitalWrite(f, LOW);
    delay(500);
    digitalWrite(f, HIGH);
    delay(500);
    digitalWrite(f, LOW);
  }

  if ( digitalRead (a == HIGH ),  digitalRead (b == LOW ));
  {
    digitalWrite(e, LOW);
    digitalWrite(f, LOW);
  }
}

void loop() {
  // put your main code here, to run repeatedly:
  pinMode(LED_BUILTIN, HIGH);
  delay(100);
  pinMode(LED_BUILTIN, LOW);
  delay(100);


目前遇到的問題是，前兩段程式碼(紅火、P檔、有無聲輸出)不會跑到

也有試過不同的寫法，都會不作用就跳到第三段

使用的板子是 Uno R3

再次謝謝幫忙解決的朋友~

--
推 byone1      :加油，我是氧氣，你ez打得很不錯
→ sdsd65676   :3Q
→ sdsd65676   :雙排ING
→ kiki761119  :我主main ad  也可走top上
推 longkiss0618:加油 我是二氧化碳 你EZ不錯
推 Asty1e      :加油 我是甲烷 你ez打的很不錯
--
※ 發信站: 批踢踢實業坊(ptt.cc), 來自: 49.216.247.157
※ 文章網址: https://www.ptt.cc/bbs/ASM/M.1516058571.A.939.html
→ sdsd65676: 身家微薄，附上稅前200P給解決的大師!
→ cocoaswifty: 把上面的if邏輯判斷放到loop()裡面
推 BrianCashman: if內所有語法與函式參數皆不正確,請修正看看
推 darptt: 好酷，根據自己的猜測修改供參考 https://goo.gl/NG4W9N
推 full0513: Setup裡不是都放基本設定而已嗎，那麽大串的判斷式應該
→ full0513: 放在loop吧，才會重複執行
推 darptt: http://bit.ly/2rn4jN0